それに、試験に失敗すれば全額返金のポリシーについて、事前に調べたほうがいいです。Shobhadoshiは間違いなくあなたの利益を全面的に保護し、あなたの悩みを思いやるウェブサイトです。もうこれ以上尻込みしないでくださいよ。 Shobhadoshiはあなたが首尾よく試験に合格することを助けるだけでなく、あなたの知識と技能を向上させることもできます。あなたが自分のキャリアでの異なる条件で自身の利点を発揮することを助けられます。 350-401絶対合格認定試験の資格を取得するのは容易ではないことは、すべてのIT職員がよくわかっています。

CCNP Enterprise 350-401 ご安心で試験のために勉強します。

なぜなら、それはCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)絶対合格認定試験に関する必要なものを含まれるからです。 Ciscoの350-401 模擬トレーリング試験に合格するのはIT業界で働いているあなたに利益をもらわせることができます。もしあなたが試験に合格する決心があったら、我々のCiscoの350-401 模擬トレーリングソフトを利用するのはあなたの試験に成功する有効な保障です。

ShobhadoshiのCiscoの350-401絶対合格試験トレーニング資料はCiscoの350-401絶対合格認定試験を準備するのリーダーです。Shobhadoshiの Ciscoの350-401絶対合格試験トレーニング資料は高度に認証されたIT領域の専門家の経験と創造を含めているものです。それは正確性が高くて、カバー率も広いです。

弊社のCisco 350-401絶対合格問題集は三種類の版を提供いたします。

我々の承諾だけでなく、お客様に最も全面的で最高のサービスを提供します。Ciscoの350-401絶対合格の購入の前にあなたの無料の試しから、購入の後での一年間の無料更新まで我々はあなたのCiscoの350-401絶対合格試験に一番信頼できるヘルプを提供します。Ciscoの350-401絶対合格試験に失敗しても、我々はあなたの経済損失を減少するために全額で返金します。

キャンパース内のIT知識を学ぶ学生なり、IT職人なり、350-401絶対合格試験資格認証証明書を取得して、社会需要に応じて自分の能力を高めます。我々社は最高のCisco　350-401絶対合格試験問題集を開発し提供して、一番なさービスを与えて努力しています。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

自分の能力を証明するために、SAP C-WME-2506試験に合格するのは不可欠なことです。 安全かつ最も信頼性の高いCisco　ServiceNow CIS-EM-JPN問題集販売サイトとして、我々はお客様の個人情報を内緒し、支払いの安全性を保証しています。 Huawei H20-923_V1.0 - 我々Shobhadoshiは一番行き届いたアフタサービスを提供します。 実際の試験に表示される質問と正確な解答はあなたのCisco　Pegasystems PEGACPLSA23V1認定資格試験合格を手伝ってあげます。 我々社サイトのCisco　HP HPE0-V25J問題庫は最新かつ最完備な勉強資料を有して、あなたに高品質のサービスを提供するのはHP HPE0-V25J資格認定試験の成功にとって唯一の選択です。

Updated: May 28, 2022