競争力が激しい社会に当たり、我々Shobhadoshiは多くの受験生の中で大人気があるのは受験生の立場からCisco　350-401資格認定試験試験資料をリリースすることです。たとえば、ベストセラーのCisco　350-401資格認定試験問題集は過去のデータを分析して作成ます。ほんとんどお客様は我々ShobhadoshiのCisco　350-401資格認定試験問題集を使用してから試験にうまく合格しましたのは弊社の試験資料の有効性と信頼性を説明できます。 弊社の無料なサンプルを遠慮なくダウンロードしてください。Shobhadoshiを利用するのは君の合格率を１００％保証いたします。 350-401資格認定試験問題集のカーバー率が高いので、勉強した問題は試験に出ることが多いです。

CCNP Enterprise 350-401 試験に合格する秘密を見つけましたか。

あなたはキャリアで良い昇進のチャンスを持ちたいのなら、ShobhadoshiのCiscoの350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)資格認定試験「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験トレーニング資料を利用してCiscoの認証の証明書を取ることは良い方法です。 それはShobhadoshiはたしかに受験生の皆さんを大量な時間を節約させ、順調に試験に合格させることができますから。Shobhadoshiの350-401 日本語認定対策問題集というものをきっと聞いたことがあるでしょう。

ShobhadoshiのCiscoの350-401資格認定試験試験トレーニング資料を持っていたら、試験に対する充分の準備がありますから、安心に利用したください。Shobhadoshiは優れたIT情報のソースを提供するサイトです。Shobhadoshiで、あなたの試験のためのテクニックと勉強資料を見つけることができます。

Cisco 350-401資格認定試験 - もっと多くの認可と就職機会を貰いたいのですか。

時間とお金の集まりより正しい方法がもっと大切です。Ciscoの350-401資格認定試験試験のために勉強していますなら、Shobhadoshiの提供するCiscoの350-401資格認定試験試験ソフトはあなたの選びの最高です。我々の目的はあなたにCiscoの350-401資格認定試験試験に合格することだけです。試験に失敗したら、弊社は全額で返金します。我々の誠意を信じてください。あなたが順調に試験に合格するように。

暇な時間だけでCiscoの350-401資格認定試験試験に合格したいのですか。我々の提供するPDF版のCiscoの350-401資格認定試験試験の資料はあなたにいつでもどこでも読めさせます。

350-401 PDF DEMO:

QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 4
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

CiscoのSAP C_S4CPR_2502試験はいくつ難しくても文句を言わないで、我々Shobhadoshiの提供する資料を通して、あなたはCiscoのSAP C_S4CPR_2502試験に合格することができます。 ISTQB CT-AI - この小さい試すアクションはあなたが今までの最善のオプションであるかもしれません。 あなたは自分の望ましいCisco Cisco 350-701問題集を選らんで、学びから更なる成長を求められます。 GIAC GRTP - paypal支払い方法は安全な決済手段のために、お客様の利益を保証できます。 また、H3C GB0-713問題集に疑問があると、メールで問い合わせてください。

Updated: May 28, 2022