それに、Shobhadoshiの教材を購入すれば、Shobhadoshiは一年間の無料アップデート・サービスを提供してあげます。問題が更新される限り、Shobhadoshiは直ちに最新版の350-401対応内容資料を送ってあげます。そうすると、あなたがいつでも最新バージョンの資料を持っていることが保証されます。 Ciscoの350-401対応内容試験に合格するのは最良の方法の一です。我々Shobhadoshiの開発するCiscoの350-401対応内容ソフトはあなたに一番速い速度でCiscoの350-401対応内容試験のコツを把握させることができます。 あるいは、無料で試験350-401対応内容問題集を更新してあげるのを選択することもできます。

CCNP Enterprise 350-401 常々、時間とお金ばかり効果がないです。

Cisco　350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)対応内容問題集は我々Shobhadoshiでは直接に無料のダウンロードを楽しみにしています。 できるだけ100％の通過率を保証使用にしています。Shobhadoshiは多くの受験生を助けて彼らにCiscoの350-401 日本語版参考資料試験に合格させることができるのは我々専門的なチームがCiscoの350-401 日本語版参考資料試験を研究して解答を詳しく分析しますから。

それで、弊社の質高い350-401対応内容試験資料を薦めさせてください。今の競争が激しい社会にあたり、あなたは努力して所有したいことがあります。IT職員にとって、350-401対応内容試験認定書はあなたの実力を証明できる重要なツールです。

Cisco 350-401対応内容 - 暇の時間を利用して勉強します。

Shobhadoshiを選ぶかどうか状況があれば、弊社の無料なサンプルをダウンロードしてから、決めても大丈夫です。こうして、弊社の商品はどのくらいあなたの力になるのはよく分かっています。ShobhadoshiはCisco 350-401対応内容認証試験を助けって通じての最良の選択で、１００％のCisco 350-401対応内容認証試験合格率のはShobhadoshi最高の保証でございます。君が選んだのはShobhadoshi、成功を選択したのに等しいです。

そして、350-401対応内容試験参考書の問題は本当の試験問題とだいたい同じことであるとわかります。350-401対応内容試験参考書があれば,ほかの試験参考書を勉強する必要がないです。

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

ISACA CISM-CN - Shobhadoshiは頼りが強い上にサービスもよくて、もし試験に失敗したら全額で返金いたしてまた一年の無料なアップデートいたします。 CiscoのAmazon AWS-Certified-Machine-Learning-Specialtyの認定試験に合格すれば、就職機会が多くなります。 あなたはShobhadoshiが提供したCisco 350-701の認証試験の問題集を購入するの前にインターネットで無料な試用版をダウンロードしてください。 ISTQB CTAL_TM_001 - あなたの全部な需要を満たすためにいつも頑張ります。 Amazon DVA-C02-KR - 今の競争の激しいIT業界では、多くの認定試験の合格証明書が君にをとんとん拍子に出世するのを助けることができます。

Updated: May 28, 2022