ShobhadoshiのCiscoの350-401基礎訓練試験トレーニング資料を手に入れたら、輝い職業生涯を手に入れるのに等しくて、成功の鍵を手に入れるのに等しいです。君がCiscoの350-401基礎訓練問題集を購入したら、私たちは一年間で無料更新サービスを提供することができます。もし学習教材は問題があれば、或いは試験に不合格になる場合は、全額返金することを保証いたします。 ほんとんどお客様は我々ShobhadoshiのCisco　350-401基礎訓練問題集を使用してから試験にうまく合格しましたのは弊社の試験資料の有効性と信頼性を説明できます。競争力が激しい社会に当たり、我々Shobhadoshiは多くの受験生の中で大人気があるのは受験生の立場からCisco　350-401基礎訓練試験資料をリリースすることです。 あなたのIT夢はどんなに大きくても、Shobhadoshiは君のそばにいていて、君の成功に助けます。

CCNP Enterprise 350-401 どんな困難にあっても、諦めないです。

CCNP Enterprise 350-401基礎訓練 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) IT認証は同業種の欠くことができないものになりました。 そのデモは350-401 試験対応試験資料の一部を含めています。私たちは本当にお客様の貴重な意見を350-401 試験対応試験資料の作りの考慮に入れます。

Shobhadoshiに会ったら、最高のトレーニング資料を見つけました。ShobhadoshiのCiscoの350-401基礎訓練試験トレーニング資料を持っていたら、試験に対する充分の準備がありますから、安心に利用したください。Shobhadoshiは優れたIT情報のソースを提供するサイトです。

Cisco 350-401基礎訓練認定試験に合格することは難しいようですね。

Shobhadoshiの助けのもとで君は大量のお金と時間を费やさなくても復楽にCiscoの350-401基礎訓練認定試験に合格のは大丈夫でしょう。ソフトの問題集はShobhadoshiが実際問題によって、テストの問題と解答を分析して出来上がりました。Shobhadoshiが提供したCiscoの350-401基礎訓練の問題集は真実の試験に緊密な相似性があります。

もし不合格になったら、私たちは全額返金することを保証します。一回だけでCiscoの350-401基礎訓練試験に合格したい？Shobhadoshiは君の欲求を満たすために存在するのです。

350-401 PDF DEMO:

QUESTION NO: 1
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 2
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which access controls list allows only TCP traffic with a destination port range of 22-433, excluding port 80?
A. Deny tcp any any ne 80
Permit tcp any any range 22 443
B. Permit tcp any any ne 80
C. Permit tco any any range 22 443
Deny tcp any any eq 80
D. Deny tcp any any eq 80
Permit tco any any gt 21 it 444
Answer: D

QUESTION NO: 5
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

もし君がCiscoのSalesforce CRT-261Jに参加すれば、良い学習のツルを選ぶすべきです。 ShobhadoshiのCiscoのSAP C_S4CPB_2502試験トレーニング資料は試験問題と解答を含まれて、豊富な経験を持っているIT業種の専門家が長年の研究を通じて作成したものです。 ISACA CISM-JPN - 何の問題があったらお気軽に聞いてください。 HP HPE7-A08 - 時間とお金の集まりより正しい方法がもっと大切です。 あなたはきっとCiscoのCheckPoint 156-587試験に合格できますから。

Updated: May 28, 2022