この目標を達成するために、我々はCiscoの350-401合格対策試験の資料を改善し続けてあなたに安心に利用させます。我々の商品とサービスに疑問があったら、我々Shobhadoshiのウェブ・サイトで問い合わせたり、メールで我々と連絡したりすることができます。あなたの購入してから、Ciscoの350-401合格対策試験ソフトが更新されたら、我々はメールであなたを通知します。 Cisco 350-401合格対策「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」認証試験に合格することが簡単ではなくて、Cisco 350-401合格対策証明書は君にとってはIT業界に入るの一つの手づるになるかもしれません。しかし必ずしも大量の時間とエネルギーで復習しなくて、弊社が丹精にできあがった問題集を使って、試験なんて問題ではありません。 我々の社員は全日中で客様のお問い合わせをお待ちしております。

CCNP Enterprise 350-401 「信仰は偉大な感情で、創造の力になれます。

CCNP Enterprise 350-401合格対策 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) 弊社の商品が好きなのは弊社のたのしいです。 IT業種で仕事しているあなたは、夢を達成するためにどんな方法を利用するつもりですか。実際には、IT認定試験を受験して認証資格を取るのは一つの良い方法です。

ShobhadoshiはもっぱらITプロ認証試験に関する知識を提供するのサイトで、ほかのサイト使った人はShobhadoshiが最高の知識源サイトと比較しますた。Shobhadoshiの商品はとても頼もしい試験の練習問題と解答は非常に正確でございます。

Cisco 350-401合格対策 - 試験に失敗したら、全額で返金する承諾があります。

ShobhadoshiのCiscoの350-401合格対策「Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR)」試験トレーニング資料はPDFぼ形式とソフトウェアの形式で提供して、ShobhadoshiのCiscoの350-401合格対策試験問題と解答に含まれています。350-401合格対策認定試験の真実の問題に会うかもしれません。そんな問題はパーフェクトと称するに足って、効果的な方法がありますから、どちらのCiscoの350-401合格対策試験に成功を取ることができます。ShobhadoshiのCiscoの350-401合格対策問題集は総合的にすべてのシラバスと複雑な問題をカバーしています。ShobhadoshiのCiscoの350-401合格対策テストの問題と解答は本物の試験の挑戦で、あなたのいつもの考え方を変換しなければなりません。

我々の提供するPDF版のCiscoの350-401合格対策試験の資料はあなたにいつでもどこでも読めさせます。我々もオンライン版とソフト版を提供します。

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

Oracle 1Z1-922 - あなたが任意の損失がないようにもし試験に合格しなければShobhadoshiは全額で返金できます。 我々ShobhadoshiはCiscoのISACA COBIT-2019試験問題集をリリースする以降、多くのお客様の好評を博したのは弊社にとって、大変な名誉なことです。 Juniper JN0-637 - あなた自身のために、証明書をもらいます。 たとえば、ベストセラーのCisco　Adobe AD0-E907問題集は過去のデータを分析して作成ます。 WGU Cloud-Deployment-and-Operations - 現在のIT領域で競争が激しくなっていることは皆は良く知っていますから、みんなはIT認証を通じて自分の価値を高めたいです。

Updated: May 28, 2022