ShobhadoshiにIT業界のエリートのグループがあって、彼達は自分の経験と専門知識を使ってCisco 350-401出題内容認証試験に参加する方に対して問題集を研究続けています。君が後悔しないようにもっと少ないお金を使って大きな良い成果を取得するためにShobhadoshiを選択してください。Shobhadoshiはまた一年間に無料なサービスを更新いたします。 Cisco　350-401出題内容試験を目前に控えて、不安なのですか。我々社のCisco　350-401出題内容問題集のソフト版を購買するに値するかまだ疑問がありますか。 弊社の350-401出題内容のトレーニング資料を買ったら、一年間の無料更新サービスを差し上げます。

CCNP Enterprise 350-401 Shobhadoshiを選んだら、成功への扉を開きます。

CCNP Enterprise 350-401出題内容 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Shobhadoshiはまた一年間に無料なサービスを更新いたします。 問題が更新される限り、Shobhadoshiは直ちに最新版の350-401 合格資料資料を送ってあげます。そうすると、あなたがいつでも最新バージョンの資料を持っていることが保証されます。

Shobhadoshiは受験者に向かって試験について問題を解決する受験資源を提供するサービスのサイトで、さまざまな受験生によって別のトレーニングコースを提供いたします。受験者はShobhadoshiを通って順調に試験に合格する人がとても多くなのでShobhadoshiがIT業界の中で高い名声を得ました。

Cisco 350-401出題内容 - 自分の幸せは自分で作るものだと思われます。

Ciscoの350-401出題内容認定試験に受かるためにがんばって勉強していれば、Shobhadoshiはあなたにヘルプを与えます。Shobhadoshi が提供したCiscoの350-401出題内容問題集は実践の検査に合格したもので、最も良い品質であなたがCiscoの350-401出題内容認定試験に合格することを保証します。

あなたは弊社の高品質Cisco　350-401出題内容試験資料を利用して、一回に試験に合格します。ShobhadoshiのCisco　350-401出題内容問題集は専門家たちが数年間で過去のデータから分析して作成されて、試験にカバーする範囲は広くて、受験生の皆様のお金と時間を節約します。

350-401 PDF DEMO:

QUESTION NO: 1
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

QUESTION NO: 5
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

さあ、ためらわずにShobhadoshiのCiscoのHuawei H20-694_V2.0試験トレーニング資料をショッピングカートに入れましょう。 Microsoft PL-300J - IT職員のあなたは毎月毎月のあまり少ない給料を持っていますが、暇の時間でひたすら楽しむんでいいですか。 College Admission ASVAB - 購入する人々が大変多いですから、あなたもミスしないで速くショッピングカートに入れましょう。 多分、Fortinet FCSS_SASE_AD-24テスト質問の数が伝統的な問題の数倍である。 Cisco 300-220 - Shobhadoshiは今まで数え切れないIT認定試験の受験者を助けて、皆さんから高い評判をもらいました。

Updated: May 28, 2022