We have three versions of 350-401 Valid Test Pattern learning materials available, including PDF, Software and APP online. The most popular one is PDF version of 350-401 Valid Test Pattern study guide can be printed into papers so that you are able to write some notes or highlight the emphasis. On the other hand, Software version of our 350-401 Valid Test Pattern practice questions is also welcomed by customers, especially for windows users. You will free access to our test engine for review after payment. How to improve your IT ability and increase professional IT knowledge of 350-401 Valid Test Pattern real exam in a short time? Obtaining valid training materials will accelerate the way of passing 350-401 Valid Test Pattern actual test in your first attempt. In the course of your study, the test engine of 350-401 Valid Test Pattern actual exam will be convenient to strengthen the weaknesses in the learning process.

CCNP Enterprise 350-401 Just add it to your cart.

As a key to the success of your life, the benefits that our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Valid Test Pattern study braindumps can bring you are not measured by money. Shobhadoshi gives you unlimited online access to 350-401 Reliable Test Papers certification practice tools. You can instantly download the 350-401 Reliable Test Papers test engine and install it on your PDF reader, laptop or phone, then you can study it in the comfort of your home or while at office.

We can assure you the proficiency of our 350-401 Valid Test Pattern exam prep. So this is a definitive choice, it means our 350-401 Valid Test Pattern practice quiz will help you reap the fruit of success. To lead a respectable life, our specialists made a rigorously study of professional knowledge about this 350-401 Valid Test Pattern exam.

Cisco 350-401 Valid Test Pattern - Trust us and you will get success for sure!

We have applied the latest technologies to the design of our 350-401 Valid Test Pattern exam prep not only on the content but also on the displays. As a consequence you are able to keep pace with the changeable world and remain your advantages with our 350-401 Valid Test Pattern training braindumps. Besides, you can consolidate important knowledge for you personally and design customized study schedule or to-do list on a daily basis. As long as you follow with our 350-401 Valid Test Pattern study guide, you are doomed to achieve your success.

One more to mention, we can help you make full use of your sporadic time to absorb knowledge and information. We would like to provide our customers with different kinds of 350-401 Valid Test Pattern practice guide to learn, and help them accumulate knowledge and enhance their ability.

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

Microsoft AZ-400 exam practice software allows you to practice on real Microsoft AZ-400 questions. SAP C_TFG61_2405 - This means with our products you can prepare for exams efficiently and at the same time you will get 100% success for sure. EMC NCA - You can totally rely on us. With Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) torrent prep, you no longer have to put down the important tasks at hand in order to get to class; with Microsoft AZ-400 exam questions, you don’t have to give up an appointment for study. Shobhadoshi's study guides are your best ally to get a definite success in Google Generative-AI-Leader exam.

Updated: May 28, 2022