And most of all, you will get reward by our 350-401 Cram Materials training engine in the least time with little effort. Perhaps you have wasted a lot of time to playing computer games. It doesn’t matter. As we sell electronic files, there is no need to ship. After payment you can receive 350-401 Cram Materials exam review questions you purchase soon so that you can study before. There is no doubt that the certification has become more and more important for a lot of people, especial these people who are looking for a good job, and it has been a general trend.

CCNP Enterprise 350-401 Never stop challenging your limitations.

It can be said that 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Cram Materials test guide is the key to help you open your dream door. Now, our 350-401 Test Cram Pdf training materials will help you master the popular skills in the office. With our 350-401 Test Cram Pdf exam braindumps, you can not only learn the specialized knowledge of this subject to solve the problems on the work, but also you can get the 350-401 Test Cram Pdf certification to compete for a higher position.

And the quality of our exam dumps are very high! The procedures of buying our 350-401 Cram Materials study materials are simple and save the clients’ time. We will send our 350-401 Cram Materials exam question in 5-10 minutes after their payment.

Cisco 350-401 Cram Materials - You may try it!

Everyone has a utopian dream in own heart. Dreams of imaginary make people feel disheartened. In fact, as long as you take the right approach, everything is possible. You can pass the Cisco 350-401 Cram Materials exam easily. Why? Because you have Shobhadoshi's Cisco 350-401 Cram Materials exam training materials. Shobhadoshi's Cisco 350-401 Cram Materials exam training materials are the best training materials for IT certification. It is famous for the most comprehensive and updated by the highest rate. It also can save time and effort. With it, you will pass the exam easily. If you pass the exam, you will have the self-confidence, with the confidence you will succeed.

Passing 350-401 Cram Materials exam can help you find the ideal job. If you buy our 350-401 Cram Materials test prep you will pass the exam easily and successfully，and you will realize you dream to find an ideal job and earn a high income.

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

Although you are busy working and you have not time to prepare for the exam, you want to get Cisco Huawei H23-021_V1.0 certificate. However, our Amazon SAA-C03 training materials can offer better condition than traditional practice materials and can be used effectively. Cisco SAP C-S4PM-2504 certificate will bring you many good helps and also help you get promoted. All precise information on the Amazon ANS-C01 exam questions and high accurate questions are helpful. Once you purchased our Microsoft GH-100 exam dump, we will try our best to help you pass Microsoft GH-100 exam.

Updated: May 28, 2022